Pro-Built Tools PB1200 Series Manual de Instalação Página 1

Installation Manual for theSINGLE Gate Operator SystemFOR PROFESSIONAL INSTALLATION ONLY!WARNING!This equipment is similar to other gate or door equip

viii GTO 4000XL Instruction Manual © 091610IMPORTANT SAFETY INSTRUCTIONS!Warning signs (2 enclosed) to be installed on each sideof the gate (3–5 feet

GTO 4000XL Instruction Manual © 091610 1Technical SpecicationsGTO/ACCESS SYSTEMS 4000XL AUTOMATIC GATE OPERATORDRIVE • Lowfrictionscrewdrive

2 GTO 4000XL Instruction Manual © 091610Before You Begin...1. Determine Charging Option for Battery: Transformer OR SolarNEVER USE TRANSFORMER AND

GTO 4000XL Instruction Manual © 091610 32. Check Direction of Gate SwingThe 4000XL is designed for PULL-TO-OPEN installations. PUSH-TO-OPEN install

4 GTO 4000XL Instruction Manual © 0916104. 4000XL Parts ListBRACKET BOX - HB301HARDWARE BAG - H301PMaster Operator Arm (1)PRO4000ARMXLCustomer Suppo

GTO 4000XL Instruction Manual © 091610 5Transformer (1) Battery (1) Control Box (1) Warning Signs (4) GTO Transmitter(1) 1. KEEP CLEAR! Gate may m

6 GTO 4000XL Instruction Manual © 0916107. Installation OverviewPull-To-Open Gates (Gate Opens into the Property)The diagram shown below is an examp

GTO 4000XL Instruction Manual © 091610 7Step 1: Close the gate and place your level against the horizontal cross member. Position the level so tha

8 GTO 4000XL Instruction Manual © 091610Step 5: Position the operator rear mount between post pivot bracket. Place a 1/2” bushing above the rear moun

GTO 4000XL Instruction Manual © 091610 9Step 8: Remove the clevis pin from the front mount and while supporting the gate operator, swing the gate a

Class RatingThe GTO 4000XL Gate Operator is intended for use with vehicular swing gates. The operator can be used in Class I, Class II, Class III and

10 GTO 4000XL Instruction Manual © 091610Install Closed Position Stop PlateThe closed position stop plate helps to stabilize the gate leaf in the clo

GTO 4000XL Instruction Manual © 091610 11Mount the Control Box and ReceiverUse mountingholes and screwsprovided to mount control box to a secure su

12 GTO 4000XL Instruction Manual © 091610Step 1 Strip approximately 3/16” of insulation from the seven wires of the operator power cable. Twist each

GTO 4000XL Instruction Manual © 091610 13IMPORTANT: • Thetransformerisdesignedandintendedforindooruse.Ifthetransformercanbeplugged

14 GTO 4000XL Instruction Manual © 091610Step 5Strip 3/16” o the ends of the low voltage wire and twist tightly. Attach these ends to the 18 VAC OR

GTO 4000XL Instruction Manual © 091610 15RED wire to POSITIVE (+) terminalBLACK wire to NEGATIVE (–) terminalREDBLACKStep 2 IMPORTANT: Connect the

16 GTO 4000XL Instruction Manual © 091610Step 4With the gate in the desired closed position PRESS & HOLD the “LEARN MAST LIMIT” button on the co

GTO 4000XL Instruction Manual © 091610 17Set Auto Close TimeThe Auto-Close Time potentiometer controls the Auto-Close feature, and determines how l

18 GTO 4000XL Instruction Manual © 091610DIP SwitchesMain DIP Switch Settings (MODES)DIP Switch #1: Soft Start/Stop ON– Soft start enabled (factor

GTO 4000XL Instruction Manual © 091610 19Input Connections • Allcontrolinputsaredry-contact,normallyopen,inputs.DONOTapplyexternalvol

Table of ContentsClass Rating ...in

20 GTO 4000XL Instruction Manual © 091610GRNCOMCOMCYCLECLOSESAFETYSHADOWLOOPCLOSEEDGEOPENEDGEEXITOPENBLKRECEIVERREDALMORGLUE BRN REDSTER INPUTSBLKSTE

GTO 4000XL Instruction Manual © 091610 21Push-To-Open Installation InformationSwinging gates shall not open into public access areas! A “Push-to-Op

22 GTO 4000XL Instruction Manual © 091610Set Control Board for Push-To-OpenMake sure the control box power switch is OFF. Use a small screwdriver to

GTO 4000XL Instruction Manual © 091610 23If this operator will be used with gates that are mounted on masonry, brick, or rock (etc.) columns, read

24 GTO 4000XL Instruction Manual © 091610Troubleshooting GuideIf your gate operator does not function properly after it is installed, use this guide

GTO 4000XL Instruction Manual © 091610 25Generation 3 Visual FeedbackSYMPTOM DIAGNOSIS CHECK:Status (clear)1 blink Cycle Terminal Shorted•Disconne

26 GTO 4000XL Instruction Manual © 091610If your GTO 4000XL Gate Operator is not operating properly, please follow the steps below: 1. First use th

GTO 4000XL Instruction Manual © 091610 27Accessories for 4000XLPOWERING ACCESSORIESLow Voltage Wire [RB509] The 16 gauge, multi-stranded, dual cond

28 GTO 4000XL Instruction Manual © 091610Residential Wireless Entry Intercom [F3100MBC]Designed for added security to your automated gate with the ab

GTO 4000XL Instruction Manual © 091610 29ADDITIONAL AccessoriesPhoto Beams [R4222]Primary “through beam” photo beam device. Provides “non-contact”

ii GTO 4000XL Instruction Manual © 091610Thank you for purchasing a GTO/ACCESS SYSTEMS 4000XL. When correctly installed and properly used, your 4000X

3121 Hartseld Road • Tallahassee, Florida, USA 32303 (850) 575-0176 • Fax (850) 575-8912Web site www.gtoaccess.com24/7 Troubleshooting Wizard: http:/

GTO 4000XL Instruction Manual © 091610 iiiIMPORTANT SAFETY INSTRUCTIONSBecause automatic gate operators produce high levels of force, consumers nee

iv GTO 4000XL Instruction Manual © 091610IMPORTANT SAFETY INSTRUCTIONSFor The ConsumerWARNING: To reduce the risk of injury or death: 1. READ AND FOL

GTO 4000XL Instruction Manual © 091610 vIMPORTANT SAFETY INSTRUCTIONSII. During Installation 1. Install the gate operator on the inside of the pr

vi GTO 4000XL Instruction Manual © 091610IMPORTANT SAFETY INSTRUCTIONS 7. To operate this equipment safely, YOU must know how to disconnect the ope

GTO 4000XL Instruction Manual © 091610 viiIMPORTANT SAFETY INSTRUCTIONSSecondary Means of Protection Against EntrapmentAs specified by Gate Operator